Milan Traders

Keeping the diverse requirements of customers in mind, we are instrumental in providing Dr.Fixit Dampguard. Dr. Fixit Dampguard is a two-component coating composed of epoxy resin, curing agent, inert pigments & properly selected fine fillers, additives in water as a medium. It has an advantage of dilution with water for application over cementitious surfaces. It is used as an internal coating for the waterproofing treatments of water tanks and building walls because it can be applied over damp surfaces, has excellent water resistance, adhesion, hardness, toughness and sets faster similar to solvent based epoxy formulations.

Dr. Fixit Repellin WR is composed of Siloxane & Silane polymers dispersed in high boiling point solvent. It is used for waterproofing of concrete & cementitious vertical walls of building because it penetrate deeply into the substrate & provides an effective water repellent protective coating. It does not changes the appearance of the substrate & the water repellant coating is uv resistant and durable.

Areas of Application:
Water repellent treatment for -

• Cement painted surfaces. 
• Concrete, mortar. 
• Clay brick surfaces. 
• Natural and artificial stones. 
• Mangalore tiled roofs. 
• Corrugated AC sheet roofing, etc.

Features & Benefits:

• Ease of application - Ready to use, simply brushable or spray applied. 
• Staining - Clear coating does not stain the treated surface. 
• Appearance - Does not change the appearance of exterior decorative coating. 
• Vapour transmission - Prevents entry of moisture into the wall, but allows moisture to evaporate out. 
• Efflorescence - Prevent efflorescence. 
• Economical - Cost effective. 
• Penetration – Due to low viscosity penetration is high, which provides the hydrophobic zone.

Method of Application
Surface Preperation 

• Surface should be dry and free from all debris, dirt, oil, grease, wax and all other contamination, which could prevent penetration. 
• Clean the saturated dirt of surface by thorough wire brushing, cleaning with compressed air followed by water washing. 
• Degrease oil & grease by using solvents like turpentine or thinners. 
• Allow the surface to dry completely before the application. 
• Seal the cracks with Dr Fixit Crack - X powder. 
• Thorough wire brushing followed by sanding with emery paper is recommended. 
• Remove the existing paint, neroo or instant lime, etc. while treating internal damp walls.

Application: 

• Apply one liberal coat of Dr. Fixit Repellin WR, simply by brushing evenly on the prepared surface. Allow the surface to dry for a minimum of 24 hrs for best results. 
• Dr. Fixit Repellin WR can also be applied with an airless spray (0.07 - 0.1 N/mm2 pressure). 
• Apply second coat wet on wet , to improve the penetration rate & performance. 
• Allow it to dry for 24 hrs.

Silicone Based Water Repellent for Exterior Brickand stone Masonry surface

Precautions & Limitations:

• Do not dilute with water or by any other means. 
• Close the container lid properly after use 
• Before applying over the natural stones like sand stone, slate or Dhollpur sampling should be done on a small area to check its suitability. 
• Before taking up application on a large area, it is advisable to check the performance of the product on a relatively small area.

Coverage:

• On porous substrate – 5 – 6 Sq meter / litre
• On low porous substrate – 7-8 Sq meter / litre.

Packaging:

• 1 , 10 & 225 litres

Shelf Life & Storage:

• Shelf life is 12 months from the date of manufacturing in unopened condition.
• Store in a cool & dry place.

Health & Safety Precautions:

• Use rubber hand gloves & safety goggles, while using Dr Fixit Repellin WR
• In case of contact with skin, wash with plenty of water.
• Keep out of reach of children’s
• Do not smoke during application

Additional Information:

• Item Code: 103