Milan Traders
Milan Traders
Mumbai, Maharashtra
Send SMS
Send E-mail

Rust Preventies

We are a leading Wholesale Trader of dr. fixit epoxy zinc rich primer, dr fixit rust remover, roff tile bonder (rtb), acc siporex block, 45 gsm fibreglass woven fabric (coated) and roff rainbow tile mate (rtm) epoxy grout from Mumbai, India.
Get CALLBACK

Dr. Fixit Epoxy Zinc Rich Primer

Dr. Fixit Epoxy Zinc Rich Primer
 
Get Best Quote
Approx. Rs 750 / 1 kgGet Latest Price

Product Details:
BrandDr. Fixit
Packaging Size1 Liter
Specific Gravity2.1 +/-0.1 (g/cc)
Test Temperature30 Deg C
Pot Life of Mixed Material150 30 Deg C (minutes)
Thickness of Application70 - 75 per coat
Inter Coat Time1 30 Deg C, (Hour)
Flash Point16 Deg C
Hard Drying Time24 hrs
Full Cure7 Days
CoverageCoverage rate will be 6 m2 / ltr at DFT of 100 microns in 2 coats

Dr. Fixit Epoxy Zinc Primer is a two-component system based on metallic Zinc and epoxy resin, hardener & additives which on mixing gives a grey coloured liquid. Dr. Fixit Epoxy Zinc Primer is recommended for coating on steel reinforcement or steel surfaces as an anti corrosion primer. The product actively resists corrosion within the confines of the repair location and avoids the generation of incipient anodes in immediately adjacent locations.

Areas Of Application
  • For Coating Of Re-Bars And Steel Surfaces.

Features & Benefits:
  • Passivation - Active Zinc-Rich System Combats Corrosion By Electro Chemicals Means.
  • Ease Of Application – Easy To Mix & Applicable By Brush Or Spray.
  • Time Saving – Saves Time Because It Dries Quickly (Touch Dry Time 15 To 45 Minutes).
  • Compatibility – Excellent Compatibility And Suitable Primer For Steel Surfaces And Can Be Over Coated By Epoxy Or Polyurethane Coatings.
  • Bonding – Bonds Strongly To Cement Concrete & Mortars.
  • Chemical Resistance – Resistance To Commonly Used Acids & Alkali.

Method Of ApplicationSurface Preparation:
  • Expose Fully Any Corroded Steel In The Repair Area And Remove All Loose Scale And Corrosion Deposits. Care Should Be Taken To Clean The Back Side Of Exposed Steel Bars As Well. Grit Blasting Is Recommended For This Purpose.
  • The Application Of Dr. Fixit Epoxy Zinc Primer Must Take Place Immediately On A Dry Steel Surface After Completion Of The Preparation Work And Not Later Than Three Hours.

Application:
  • Apply First Coat Of Dr. Fixit Epoxy Zinc Primer Using A Suitable Brush, Making Sure That The Back Of Exposed Steel Reinforcement Bars Are Properly Covered.
  • Apply Second Coat, In Case Of Any Discontinuity In The First Coat, After Drying Of First Coat For Minimum 1 Hour.
  • The Primed Surface Should Not Be Left Exposed For A Longer Time. The Application Of Concrete Repair Material Should Proceed As Soon As The Dr. Fixit Epoxy Zinc Primer Is Fully Dried.

Precautions & Limitations:
  • Dr. Fixit Epoxy Zinc Primer Should Not Be Applied When The Temperature Is Below 10Oc & Is Above 40Oc.
  • It Is Flammable So Prevent From Naked Flame.
  • Keep Away From Source Of Ignition.
  • In Case Needed, Fire Extinguish With Co2 Or Foam Extinguisher

Health & Safety Precautions:
  • Like for all chemical products, caution should always be exercised. Protective clothings such as gloves and goggles should be worn.
  • Treat any contact to the skin or eyes with fresh water immediately.
  • Should the product be accidentally swallowed, do not induce vomiting but call for medical assistance immediately.

Additional Information:
  • Packaging Details: 1 Liter
Yes! I am Interested
View PDF
Get CALLBACK

Dr Fixit Rust Remover

Dr Fixit Rust Remover
 
Get Best Quote
Approx. Rs 120 / PieceGet Latest Price

Product Details:
Packaging Type500 ml, 1 Liter
ColorBrown
CoverageApproximately 15 to 20 m2 / liter
AppearanceWater consistency liquid
PhAcidic
Sp gravity1.20 +/- 0.03

Dr. Fixit Rust Remover is based on chloride free chemical & additive solution in water. it is used as rustremover which effectively cleans rust from steel surfaces, before application of any protective coating.

Areas of Application:
  • On re-bars during repairs to reinforced concrete structures.
  • Maintenance of mild steel structures like tanks, water pipelines, shuttering plates and other corroded steel surfaces.

Features & Benefits:
  • Ease of application - Ready to use, easily applicable by brush.
  • Penetration & effect - effective rust removal even from areas difficult to reach & penetrate.
  • Chloride free - Contains no chloride hence no chance of enhancing further corrosion.
  • Economical - Cost effective because of good coverage.

Method of Application
Surface Preparation:
  • In Case Of Heavy Rusting Of Steel Reinforcement, M.S. Pipelines, M.S. Plates Or Any Other M.S. Surface, Removethe Loose Rust By Wire Brushing, Chipping, Hammering Or Grinding So That Majority Of Rust Scale Is Removed.

Application:
  • Apply Dr. Fixit Rust Remover On Affected Surface By Using Cotton Waste Swab Or By Brush Application. Leave The Surface To React With Dr. Fixit Rust Remover For At Least 15 To 30 Minutes.
  • The Rusty Surface Will Change Its Colour To Original Blackish Steel, Remove The Same With Cotton Cloth.
  • Then Remove The Loose Rust Particles By Scrubbing Or Simple Dusting With The Brush.
  • Wash The Steel Surface With Water Jet To Remove All The Acidic Residue Left On The Bar, And Clean With Cotton Cloth

Finish:
  • When Applied Over Corroded Reinforcement Steel, Wash The Surface With Clean Water Before Taking Up Further Work Of Repairs. Precautions & Limitations
  • Dr. Fixit Rust Remover Is Acidic In Nature, When Applied To Clean The Rusted Rebars. Ensure That Traces Of Acid Are Removed Completely By Washing With A Water Jet, Before Applying Coatings Or Primers.
  • For The Rough Removal Of Rust, Opt For Shot Blasting.

Shelf Life & Storage:
  • Shelf life is 24 months from the date of manufacturing in unopened condition. Store at cool & dry place away from sunlight & naked flames.

Health & Safety Precautions:
  • As with all chemical products, caution should always be exercised.
  • Use of safety hand gloves is recommended.
  • Treat any contact to the skin or eyes with fresh water immediately.
  • Should any of the products be accidentally swallowed, do not induce vomiting but call for medical assistance immediately.

Other Product Categories Available
DR. FIXIT has wide range of Waterproofing & Construction chemicals which includes,
  • Waterproofing Products 
  • Exterior Coating Products
  • Repair Products 
  • Tile Fixing Range
  • Sealants 
  • Concrete Admixtures
  • Flooring Products 
  • Grouts
Yes! I am Interested
View PDF
Get CALLBACK

Roff Tile Bonder (RTB)

Roff Tile Bonder (RTB)
 
Get Best Quote
Approx. Rs 20 / NumberGet Latest Price

Product Details:
Minimum Order Quantity100 Number
ApplicationTile Fixing
FormLiquid
UsageContraction
Initial SettingNo
Open Time5 to 15 minutes
Adjustability5 to 10 minutes
Water15 Liter

On-site mix for enhancing the strength and workability of cement

Roff Tile Bonder is economical on-site mix additive to be mixed with cement, for fixing of tiles. Roff Tile Bonder exhibits very high water retention and thus reduces the absorption of water in to porous substrates. It provides workability, sufficient sag resistance as well as appropriate setting time. The adjustability is good even at low dosages and high ambient temperatures. It makes cement self-cured.

Areas of Application:

  • Roff Tile Bonder (RTB) & cement slurry is used for fixing tiles on conventional machan / Levelling bed application. For fixing tiles on wall, Roff Tile Bonder is to be mixed with cement and / or sand and can be applied by notch trowel.

Features:
  • Improves adhesion
  • High open time & antisag properties
  • Good adjustability time with high water retention even at elevated temperature
  • It can be used with both grey and white cement
  • Suitable for Ceramic & Vitrified tiles

Benefits:
  • Exceptional bonding properties, compaired to the traditional conventional machhan
  • Easy to use, no special tools required
  • Economical solution for tile fixing
  • Low VOC environmentally safe

Method of Application
Surface:
  • The surface should be sound, clean, and free from dirt, oil or grease before application of conventional cement machan or levelling bed.
  • Ideally levelling bed / Machan should be prepared using Cement : Sand : Water in the ratio of 1 : 6 : 1.

Joints Preparation:
  • } Expansion joints coinciding with joints in the substrate should be incorporated at the design stage with spacing at 5 mtrs maximum and it is not to be covered with tiles.

Mixing:
  • Roff Tile Bonder to be mixed with cement & sand for your tile fixing.

Method Of Application (Type 1) 
For Flooring
With cement
Cement : 50 Kg (approx. Volume 35 Ltrs.)
Roff Tile Bonder : 1 Kg (approx. Volume 1.3 Ltrs.)
Water : 15 Ltrs.
  • Take 10 ltrs of water in a clean and dry vessel. Slowly, mix 50 Kg Cement and 1 Kg of Roff Tile bonder under stirring to obtain a uniform lump free consistency. A forced action mixer attached with paddle stirrer for 2 - 3 minutes) is highly recommended. Finally, add 5 Ltrs. Of Water to get a soft and smooth pastes. “Water dosage can be decreased / increased depending upon cement and sand available at site to achieve the desired consistency for application”  For hand-mixing, the total quanity of the mixture should be reduced to enough to ensure a soft and smooth, lump-free paste. 
  • Mix the quantity, which can be used within 30 minutes.

With cement & Sand
Cement : 25 Kg (approx. Volume 17 Ltrs.)
Sand (0.1 - 0.5 mm) : 25 Kg (approx. Volume 17 Ltrs.)
Roff Tile Bonder : 1 Kg (approx. Volume 1.3 Ltrs.)
Water : 15 Ltrs.
  • Take 10 ltrs of water in a clean and dry vessel. Slowly, mix 25 Kg Cement , 25 Kg River Sand (0.1 – 0.5 mm ) and 1 Kg of Roff Tile bonder under stirring to obtain a uniform lump free consistency. A forced action mixer attached with paddle stirrer for 2 – 3 minutes) is highly recommended. Finally, add 5 Ltrs. Of Water to get a soft and smooth pastes. “Water dosage can be decreased / increased depending upon cement and sand available at site to achieve the desired consistency for application”  For hand-mixing, the total quanity of the mixture should be reduced to enough to ensure a soft and smooth, lump-free paste.
  • Mix the quantity, which can be used within 30 minutes.

Additional Information:
  • Pay Mode Terms: T/T (Bank Transfer)
Yes! I am Interested
View PDF
Get CALLBACK

ACC Siporex Block

ACC Siporex Block
 
Get Best Quote
Approx. Rs 10 / NumberGet Latest Price

Product Details:
Minimum Order Quantity1000 Number
BrandACC
Size12 x 4 x 2 inch
MaterialCement
Usage/ApplicationBlocks
ShapeSquare
I deal inNew only

We are the Leading Supplier & Distributor of Hardware Products & Contraction Metrials form Mumbai for more details or Buy Kindly contact to us.

Additional Information:
  • Pay Mode Terms: T/T (Bank Transfer)
Yes! I am Interested
Get CALLBACK

45 Gsm Fibreglass Woven Fabric (coated)

45 Gsm Fibreglass Woven Fabric (coated)
 
Get Best Quote
Approx. Rs 1,150 / PieceGet Latest Price

Product Details:
Minimum Order Quantity1 Piece
PatternStripes
UseExternal thermo insulating composite system (ETICS) & External Insulating Finish System (EIFS) External & Internal Plaster Reinforcement. Marble Slab Reinforcement. Asphalt reinforcement (Roof waterproofing) Reinforce lightweight construction boards. As a reinforcement in LIQUID MEMBRANE WATERPROOFING
Width44-45"
Grid Size2.5 mm
Yarn TexWarp-66, Weft-33
DensityWarp-10
Treated Woven Mass45g/m2
Woven StructureLeno
Resin Content18%
Tensile StrengthWarp-Greater Than 600 (N/5 x 20 cm) Weft-Greater Than 420

We offer 45 Gsm Fibreglass Woven Fabric (coated) to our clients.


Additional Information:
  • Pay Mode Terms: Other
  • Packaging Details: Coated Alkali Resistant Fiberglass Mesh Cloth is wound in paper tubes. The quantity of fabric wound is 50mtr and a width of 1mtr. Each roll is packed in a shrink film or plastic bag.
Yes! I am Interested
Get CALLBACK

Roff Rainbow Tile Mate (RTM) Epoxy Grout

Roff Rainbow Tile Mate (RTM) Epoxy Grout
 
Get Best Quote
Approx. Rs 2,500 / UnitGet Latest Price

Product Details:
Minimum Order Quantity5 Unit
Item CodeT13
ApplicationConstruction Chemicals / Tile Joint Sealent
BrandROFF
AppearanceMatte,Polish,Gloss
Weight1 Kg
I deal inNew only

This epoxy adhesive is ideal for filling the tile joints of high traffic areas, such as hospitals, factory floors and kitchens, due to its strength and durability.
A resin-based epoxy tile joint filler, this epoxy adhesive exhibits stain resistant, chemical resistant,hard wearing and impervious properties. It has a high degree of resistance to abrasion and impact making it ideal to seal the joints between tiles in areas that receive extremely high footfall. It ensures an extremely hygienic surface that is impermeable and can withstand a high degree of wear and tear.
Yes! I am Interested
View PDF
Get CALLBACK

ROFF BOND REPAIR

ROFF BOND REPAIR
 
Get Best Quote
Approx. Rs 53 / KilogramGet Latest Price

Product Details:
Packaging SizeRoff Bond Repair is used as a bonding agent between old & new concrete, for cementitious substrates
FeaturesMulti-purpose use as a bonding agent, modifier for cement-sand & concrete mixes in building repairs
TypeSBR
Usage/ApplicationFollowing are directions for the use of Roff Bond Repair for structural repairs and rehabilitation o
Packaging TypeBottle
Shelf LifeFollowing are directions for the use of Roff Bond Repair for structural repairs and rehabilitation o

Roff Bond Repair is a Styrene Butadiene Polymer Based Latex specially developed to form a matrix with cement.
Areas of Application
Roff Bond Repair is used as a bonding agent between old & new concrete, for cementitious substrates, waterproof coating to small areas in bathrooms, balconies & small roofs. It is also effective to make repair mortars & concrete in building rehab works.

Additional Information:
  • Item Code: W01
  • Packaging Details: Following are directions for the use of Roff Bond Repair for structural repairs and rehabilitation of concrete structures. } Reach the sound concrete and clean the reinforcement bars with wire brush to remove loose scales. } Clean with jet of water to remove all dust and loose particles. } Apply a passivator coat : 1 part cement : 1 part Roff Bond Repair, coat on cleaned reinforcement bars and allow to dry for 2-3 hours.
Yes! I am Interested
View PDF
Get CALLBACK

Birla White Cement

Birla White Cement
 
Get Best Quote
Approx. Rs 1,085 / 50 KGGet Latest Price

Product Details:
Minimum Order Quantity10 50 KG
BrandBirla
ColorWhite
ApplicationCement
UseContraction

We are the Leading Supplier & Distributor of Hardware Products and Contraction Metrials form Mumbai for more details or Buy Kindly contact to us.

Additional Information:
  • Pay Mode Terms: T/T (Bank Transfer)
Yes! I am Interested
Get CALLBACK

Industrial Sand

Industrial Sand
 
Get Best Quote
Approx. Rs 2,000 / OnwardsGet Latest Price

Product Details:
Minimum Order Quantity100 Onwards
MaterialSand
HardnessMohs 7.0-8.0
Specific Gravity3.76-4.02g/cm3

We are the Leading Supplier & Distributor of Hardware Products & Contraction Metrials form Mumbai for more details or Buy Kindly contact to us.

Additional Information:
  • Pay Mode Terms: T/T (Bank Transfer)
Yes! I am Interested
Get CALLBACK

Rainbow Tile Mate Wide Additive

Rainbow Tile Mate Wide Additive
 
Get Best Quote
Approx. Rs 83 / PieceGet Latest Price

Product Details:
Usage/ApplicationCan be used for joint width upto 12 mm } Non Shrinking & non Cracking } Provides Waterproofing } Non
BrandROFF
Item CodeT14

Roff RTM Wide is cementitious tile joint filler for wider joints of non porous , pavement tiles. It filles wider gap without cracking & shrinking when mixed with Roff RTM Wide Additive. It is a factory prepared mix of portland cement, aggregates & pigments which provides washable & long lasting color.

Additional Information:
  • Item Code: T14
Yes! I am Interested
Get CALLBACK

C01 Roff Hyguard EX C01

C01 Roff Hyguard EX  C01
 
Get Best Quote
Approx. Rs 1,044 / BarrelGet Latest Price

Product Details:
Usage/ApplicationThoroughly brush and clean the surface mechanically to remove all laitance,loose particles,mortar
MaterialPOLYMER MODIFIED CEMENTITIOUS WATERPROOF COATING

Roff Hyguard EX is a ready to use two pack polymer modified cementitious protective and waterproof coating.
 Areas of Application
ROFF HYGUARD EX is used as a waterproof coating in basements, roof slabs, water retaining structures, sunken slabs, terrace slabs, water tanks, bathrooms, damp walls, foundations etc.

Additional Information:
  • Item Code: C01
  • Packaging Details: Mix in a clean container, slowly by adding the powder to the liquid in a ratio of 3 : 1 (powder: liquid). Stir with slow speed mixer and a proper paddle. Mix for 2-3 minutes until free from lumps. } Apply the 1st coat of mixed material using a short, stiff bristle brush over the prepared surface and allow it to dry for 4-6 hours. The first coat must be well applied into the undulations of the surface. } When 1st coat is dry in 4- 6 hrs, apply the 2nd coat. } It is mandatory to protect the coating by overlaying mortar or plaster. } If applied on horizontal surfaces, the screed must at least be 50 mm thick in M20 concrete. Consult Roff for technical details } Curing must be done by only placing a wet hessian at least upto 72 hrs after drying, and thereafter by proper curing with water.
Yes! I am Interested
View PDF
Get CALLBACK

Roff SupercreteR01

Roff SupercreteR01
 
Get Best Quote
Approx. Rs 203 / KilogramGet Latest Price

Product Details:
CategoryAcrylic Based Polymer Coating

Roff Supercrete is a white liquid Acrylic Polymer admixture for waterproof coating, bonding agent, repair-mass-in-fill and non-shrink polymer cement grout system.
Areas of Application
Roff Supercrete is recommended for use in the following areas of application } Waterproof and damp-proof coating in the form of cement slurry/cement mortar } As a bonding agent on cold/constructiopn joints } Concrete repair as a patching mortar } Protective layer for cementitious surface } Injection into concrete/rock structures in the form of cement slurry } As a mortar or slurry coating for better resistant to chemical attack

Additional Information:
  • Item Code: R01
  • Packaging Details: a) Waterproof cement slurry Mix 1 Litre of ¿¿¿Roff Supercrete¿¿¿ liquid with 2 Kg of fresh 43 or 53 grade OPC (do not use lumpy or air set OPC or PPC) thoroughly to make smooth brushable consistency. Such mixed material (say 3 Kg.) will provide the coverage between 1.5 m2 and 2.0 m2 depending upon surface texture/porosity on a prepared surface. The thickness varies from 0.9 to 1.1 mm. b) Bonding coat between two courses of concrete/mortar OPC = 1.75 Kg. Zone III Sand = 1.75 Kg. Roff Supercrete = 1 ltr. Mix to a smooth consistency and then apply by brush. Within 5 minutes of application start placing the concrete over it and compact the mass as usual within 45 minutes. Critical Cold joints/construction joints are not only be well bonded but also will not give rise to any future water leakage. 4.5 kg of mixed material will cover around 2.20m2 to 2.60m2 in single coat, which is recommended. The pouring of new concrete/ mortar should be completed within 45 minutes of Bond Coat application
Yes! I am Interested
View PDF
Explore More Products
Get Best Quote
Get Best Quote
Get Best Quote
Get Best Quote
X
Find Us Yash Chheda (Partner) 8/9, Mehta Mansion, Dr. Ambedkar Road, lalbaug, Mumbai - 400012, Maharashtra, India
SEND SMS
SEND E-MAIL
Share Us: